Author Topic: Dingoo and Dingux troubleshooting and FAQ guide  (Read 91316 times)

borus

Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #30 on: September 09, 2010, 10:30:01 am »
I believe the following method may be added to the troubleshooting:

Safe zImage/rootfs replacement (solves freeze at dingux logo)

Domian

  • Guest
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #31 on: September 09, 2010, 10:47:46 am »
I believe the following method may be added to the troubleshooting:

Safe zImage/rootfs replacement (solves freeze at dingux logo)
that, btw, didn't solve my problem. It only worked with the formatting.

But if the problem appears after using the card for a while, the forced together defrag may help.

60659

  • *
  • Posts: 5
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #32 on: December 04, 2010, 04:37:34 pm »
[ A-320, white, 9331 ]
I have 'Segmention fault' version.
I've tried CHKSDK - there was nothing to repair.
I've tried reformatting - no changes.
What else left to do?

Bouvrie (OP)

Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #33 on: December 05, 2010, 01:20:04 am »
I'm thinking reformatting, as CHKDSK usually doesn't help much anyway, but is not so drastic as formatting.

Try another utility to format your card, and if that doesn't help try deleting and creating a partition on the card.
Write/save problems? Segmentation faults? Black screens? Read the Troubleshooting and FAQ guide first to fix your issues! :)
SD Card readonly/corruption issues? Chkdisk /F and steer clear from DMenu: use GMenu instead!

Shyfer

  • Guest
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #34 on: March 24, 2011, 07:48:29 pm »
My dingoo keept freezing at the boot with the dingux logo, solved by formatting the card with HP USB Disk Storage Format Tool, NOTHIING else could fix it. I THINK that this only formats rebuilding the partition table and setting the bootable flag, not sure.

pavelsh

  • *
  • Posts: 21
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #35 on: June 06, 2011, 06:42:49 pm »
what means "Kernel panic - not syncing: Fatal exception in interrupt"? It appears if I select too big clock for link in Gmenu2x. It starts about 410-420 MHz.

SilverhawkBR

Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #36 on: June 07, 2011, 01:26:33 am »
Well, some dingoos can overclock more and others less.

For example, i reach 445Mhz unstable, for example, but some people barely reaches the 385Mhz with stability.

Just lower your clock until its fine.

pavelsh

  • *
  • Posts: 21
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #37 on: June 07, 2011, 11:41:55 am »
But I can perfectly set 430 MHz in app, like picodrive.

SilverhawkBR

Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #38 on: June 07, 2011, 11:17:50 pm »
Yes you can. Tough it will crash, you just have to find your very own max overclock value in this case. Most dingoos can overclock to 430Mhz, but some cant, so you just have to keep it a little lower.

smida3

  • *
  • Posts: 142
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #39 on: September 28, 2011, 08:54:46 am »
Thanks for the FAQ
NI !

Hipno702

  • Guest
Re: Dingoo and Dingux troubleshooting and FAQ guide
« Reply #40 on: September 30, 2011, 02:57:10 am »
i'm trying to install the dual-boot right now. I've installed the rockbox driver in flash mode but when i type in the commands usbtool-win 1 hwinit_ILI9338.bin 0x80000000
   usbtool-win 1 zImage_dual_boot_installer_ILI9338 0x80600000 i keep getting
[ERR] memory could not be allocated. what am i doing wrong? cmd is in the same directory as the dual boot and dingux folders but everything i try doesn't work. can anyone help?

 

Post a new topic